17-AWG hook-up wire BLACK 100m

If you buy CONNECTORS, you need these: 50x ATX crimp terminals FEMALE Mini-Fit-Jr for ATX, PCI-E and EPS, made for 18 AWG and 17 AWG (1.00mm²). The difference to the 15-16 AWG FEMALE ATX version can be seen in the second photo. The only difference is the length of the conductor "wings", which wrap around the conductor of the wire when crimped, otherwise both size versions are 100% compatible with all connectors and mating terminals. FEMALE crimp terminals are always used for CONNECTORS. These are the best female crimp terminals for ATX, PCI-E and EPS connectors manufactured in the USA by the MOLEX company. You can use these Mini-Fit-Jr crimp terminals on all common wire sizes, which you find e. g. in PC / computer systems on PSU / power-supplies. Crimping of these female ATX crimp terminals on 18AWG (0.8 mm²) and 17AWG (1.00 mm²) electrical wire will be perfect when the electrical wire has the common outer diameter (including insulation) between 1.7 mm to 2.4 mm. MDPC-X recommends electrical wire with PVC insulation for crimping female ATX crimp terminals. You can find electrical wire here at MDPC-X and at some of our MDPC-X Stores around the world or in shops for electrical supplies. Combine these female ATX crimp terminals with our legendary Crimping Tool for ATX Mini-Fit-Jr crimp terminals by MDPC-X plus the original Pin Remover / Extraction Tool for ATX crimp terminals by the MOLEX company and you will have the full joy of shortening or building your own cables and removing cables. A relatively small investment into absolute freedom in the world of creativity, cable sleeving and technology.

SATA Crimp Connector by MOLEX with straight wire insertion (including 10 crimp terminals): This is the original SATA crimp connector, manufactured in the USA by the MOLEX company. The highest precision connectivity with 100% specification matching, by the company which makes the specifications - the MOLEX company. This is just a different league. You have to use these SATA crimp connectors in combination with the supplied crimp terminals and 18 AWG, 17 AWG or our special 15 AWG wire. We supply 10 original MOLEX crimp terminals with 1 connector, even that you will only need 5 terminals. You have to crimp these terminals onto your wire with the Crimping Tool. Enjoy the original!

Use this wire size in combination with MICRO sleeve. Very experienced sleevers will also use it with SMALL sleeve, but it's not for the average user, because it requires perfect "length-stretch and fix the sleeving" skills. Do NOT use it with XTC, only use XTC if you bundle 2 or more of these wires into one XTC sleeve. Black hookup wire is perfect to slightly tone down light cable sleeving colors. It's typically used with black sleeving and carbon sleevings, which include black. Stranded 17 AWG hook-up wire Black, of course 100% tinned copper, no markings and coming as a beautiful large inner diameter ring to prevent spiral shaping as much as technically possible. At an outer diameter of only 2.00 mm, this is a class of its own. Maximized conductor size for lowest resistance, minimized outer diameter: This is the uncompromising MDPC-X 17 AWG hook-up wire Black, of course 100% made in Germany.   What's better than a high cross-sectional diameter? An even higher one! The bigger the cross-sectional diameter, the lower the electrical resistance. Heating issues at high load? Not anymore! 18 AWG is the standard size used in todays computers. At an outer diameter of only 2.00 mm MDPC-X now brings you the next bigger conductor size of 17 AWG, because we can. The outer diameter of only 2.00 mm allows you to use 17 AWG now in the same way as you used 18 AWG before - ideal for push-in connectors like SATA THROUGH. This wire exceeds 18 AWG in electrical performance while being smaller or the same in outer diameter. Technical Data: This wire comes in rings of 10 meter lengths Tinned copper conductor in PVC insulation according to VDE 0812 -30°C to 80°C PVC insulation, flame resistant according to VDE 0482-332-1-2. Once braided with MDPC-X cable sleeving it is resistant from -58°C to +155°C. Short term peaks of 215°C can then also be handled without structural degradation Constant operating voltage: 900V, Test voltage 2.500V Electrical resistance per kilometer: max 18.5 Ohm Attention: Hook-up wire is a relatively heavy item. It can quickly raise the weight based shipping cost to the next level.

If you buy HOUSINGS, you need these: 50x ATX crimp terminals MALE Mini-Fit-Jr for ATX, PCI-E and EPS, made for 18 AWG and 17 AWG (1.00mm²). The difference to the 15-16 AWG MALE ATX version can be seen in the second photo. The only difference is the length of the conductor "wings", which wrap around the conductor of the wire when crimped, otherwise both size versions are 100% compatible with all housings and mating terminals. MALE crimp terminals are always used for HOUSINGS. These are the best male crimp terminals for ATX, PCI-E and EPS housings manufactured in the USA by the MOLEX company. You can use these Mini-Fit-Jr crimp terminals on all common wire sizes, which you find e. g. in PC / computer systems on PSU / power-supplies. Crimping of these male ATX crimp terminals on 18AWG (0.8 mm²) and 17AWG (1.00 mm²) electrical wire will be perfect when the electrical wire has the common outer diameter (including insulation) between 1.7 mm to 2.4 mm. MDPC-X recommends electrical wire with PVC insulation for crimping male ATX crimp terminals. You can find electrical wire here at MDPC-X and at some of our MDPC-X Stores around the world or in shops for electrical supplies. Combine these male ATX crimp terminals with our legendary Crimping Tool for ATX Mini-Fit-Jr crimp terminals by MDPC-X plus the original Pin Remover / Extraction Tool for ATX crimp terminals by the MOLEX company and you will have the full joy of shortening or building your own cables and removing cables. A relatively small investment into absolute freedom in the world of creativity, cable sleeving and technology.

SATA Connector 90° THROUGH by MOLEX: This is the original 90° SATA connector THROUGH, manufactured in the USA by the MOLEX company. The THROUGH version is made for wires going through the connector, so you can install them in a row of multiple connectors. The cap of the THROUGH connector is open on both sides, for the pass through of the wire. For the last connector on the wire you can use the SATA crimp connector. The wires (18 AWG, 0.75 mm², 17 AWG 1.00 mm²) are simply pressed down completely into the "blades" of the connector with a flat screwdriver or similar wide object, while you hold the connector stable on a surface. The "blades" of the connector cut through the wire-insulation and make contact to the wire core. You can see the procedure on the second photo in the product gallery. A different league in the world of connectors. The highest precision connectivity with 100% specification matching, by the company which makes the specifications - the MOLEX company. Enjoy the original!